MetalSafe Sealant

A thorough inspection of the roof will help you identify potential entry routes for water and the conditions that contribute to leaking. Look for adequate drainage, and water staining (to help you identify trouble areas). Inspect carefully around vents, rooftop units, skylights, solar panels. Look for loose screws/bolts, damaged panels, deteriorated butyl strips, deteriorated sealants, contaminants, holes, and punctures.

If you need any help along the way, reach out to our Product and Application Support Team by phone: 1-855-382-0173 or email: Support@ShopLiquidRubber.com We can walk you through the whole process.

*Liquid Rubber is intended as a restoration product, check with local building code guidelines for over living space roof requirements in your area.

SELECT YOUR SEALANT

• MetalSafe Sealant - Black
• Color Sealant - 9 high quality colors to choose from including clear.
• Silicone Roof Coating - White only. Allows for 1 coat application.

PICK THE RIGHT PREP & PRIMER

• Cleaning - Liquid Rubber Deck & Patio Cleaner
• Cracks, joints & voids - Liquid Rubber Sealant & Adhesive Caulk, GeoTextile or Seam Tape
• Priming - If rust is present, a water-based rust primer or converter will be required when using Color Sealant and Silicone Roof Coating.

Liquid Rubber roofing products must be installed on a clean, dry, and structurally sound surface that is free of sharp edges, dirt, debris, oil, grease, coal tar, mastics, flaking paint, silicone, or other contaminants.

• Remove any cracked or peeling silicone caulking if present.
• Remove heavy rust/scale.
• Pressure Washing is recommended to provide a clean bonding surface. Liquid Rubber Deck & Patio Cleaner is recommended to remove tougher contaminants prior to power washing.
• Use masking tape for areas not to be painted and remove while the Primer/Coating is still wet. Apply masking tape for each coat.

Filling seams, joints and imperfections:

• Fill screw holes, cracks, and joints ( ¼” and larger) with Liquid Rubber Sealant & Adhesive. *Allow 24 hours to cure.
• Then bridge all cracks, joints and seams with Liquid Rubber Seam Tape or Liquid Rubber Geo-Textile using the 3 course method (Sealant/Coating - Geo-Textile - Sealant/Coating).
• Apply rust primer/converter over rust spots as necessary. Liquid Rubber MetalSafe Sealant does not require rust primer/converter.

Once your preparation is complete, clean, and dry you can begin your full field application.

• Begin applying your selected Liquid Rubber waterproof coating in the farthest corner and work toward your exit. Work in manageable sections (i.e. 10ft x 10ft). Lap onto adjoining sections maintaining a wet edge. When lapping onto a dry section, overlap by 4-6 inches.
• Inspect each coat as you go for blisters, pinholes, etc and repair as necessary.
• Apply additional coats in alternating directions to help ensure uniform membrane thickness. *Apply final coat in the direction of slope for positive drainage. Use all recommended material.
• Remove painters tape while coating is still wet. Apply masking tape for each coat (or just stay shy of the termination line). 4. Allow to cure completely. **Initial cure (set) within 48 hours or until completely dry.

Allow to cure completely. **Initial cure (set) within 48 hours or until completely dry.

• Apply in dry, warm temperatures - between 10C°/50F° and 30C°/86F°, including overnight temperatures.
• Do not apply in wet conditions or if rain, fog or dew is forecasted within 24 hours.
• Out of hot, direct and intense sun.
• Below 80% humidity.
• Make sure what you’re coating is at least 5 degrees above the dew point of the environment (Click here for more info).

Stay organized and limit clean up by following these setup tips:  

1. Set out a tarp or large piece of cardboard to keep containers and tools on when not in use. 
2. Wrap tools in plastic to keep them moist between coats (kitchen wrap is fine). Best to use disposable brushes and rollers. 
3. If there is a spillage, soak up as much material as possible with rags. 
4. Refer to the product Safety Data Sheet for personal protective equipment recommendations.
5. If the spillage dries, scrape it off with a razor/ scraper or use a wire brush to remove.
6. Do not use solvents or solvent based cleaners, adhesives, and paints near your working area.
7. Clean your Color Sealant spillages with soap and water as much as possible.
8. MetalSafe & Silicone should be cleaned up immediately with mineral spirits (sparingly) to weaken surface, and use baby oil to clean sealant off of skin 

*Test inconspicuous area first to ensure no discoloration on surface